( items)

Sales & Advice
0191 645 1685

£41.75Egg (white) EPDM 1-4mm 25kg bag 

Egg (white) EPDM 1-4mm 25kg bag £ 41.75 In stock
Colour

Beige

Black

Blue

Bright Yellow

Brown

Dark Grey

Earth Yellow

Egg

Green

Light Blue

Light Green

Light Grey

Mid Grey

Orange

Pink

Post Box Red

Purple

Red

Teal

Tierra

Agua


Quantity:
 

Wetpour
Hardwearing colourfull rubber play and sports surfacing

 

What is it !

Wet Pour rubber safety surfacing is suitable for playground installations where impact absorbent surfacing is a requirement up to the appropriate Maximum Free Fall Height (see chart below). It can be used around complex configurations of playground equipment and ground contours.

Wet Pour surfacing for playgrounds is slip-resistant and non-abrasive to young children. It is porous, so no puddles.

Colourful graphics can be created within the Wet Pour for games or emblems. This is done by designing a stencil and cutting out the top layer colour to replace it with contrasting colours.

 

The Benefits of MonsterMulch Wetpour !

Monstermulch have tried and tested many supply sources for wetpour materials over the decades. We have the aquired expertise to know which materials perform well and which perform poorly over the expected life of a wetpour surface.

We can supply and install or we can supply with all technical information you may need to know.

The Monstermulch materials have the following qualities:-

  • Manufactured in the UK.
  • High spread rate volume to weight ratio, thus cheaper per kg
  • High elasticity.
  • Less filler such as calcium carbonate
  • Full fade resistant colour
  • Quotes and methods provided
  • Installation service available
How it Works !

 

1) Solid sub base & border is required
2) It is porous
3) Mix and lay base crumb (10% resin)
4) Mix and lay EPDM top (20% resin)
5) Allow 12 hours for each layer to cure

The required sub bases for wetpour

  1. Concrete or open-textured tarmac
  2. MOT Type 1 stone (50mm or more)

The Standard Wetpour Method
(2 layer process)

The base layer provides the safety cushion effect. It is recycled 2-6mm crumb bonded rubber, mixed on site using special equipment and laid to exacting standards usually 30-50mm with 10% resin. It is relatively cheap costing about £14 per square metre at 30mm (£4.5 per 10mm approx) .

 
Base layer per 1m 2-6mm crumb Resin
20mm depth 12.5 kg 1.25 kg
25mm depth 15.6 kg 1.56 kg
30mm depth 18.75 kg 1.87 kg
35mm depth 21.9 kg 2.19 kg
40mm depth 25 kg 2.5 kg


The top EPDM layer. Recommeded to be 20mm it is a specifically manufactured polymer of  1-4mm granules designed to be very hard wearing and colourfull. It is more expensive at about £45 per square metre depending upon which colour.

Top layer per 1 sqm 1-2mm EPDM Resin
15mm depth 12.5 kg 2.5 kg
20mm depth 16.7 kg 3.33 kg
25mm depth 21.0 kg 4.17kg

 

Critical Fall Height Requirements

Don't worry, we'll calculate the appropriate materials for you !
and install if you wish !

 

Suggested Wetpour Mixer & Tools

   

 

BARON WETPOUR MIXERS

Forced action pan-type wetpour mixer available in a range of petrol or diesel engines. Designed for mixing rubber granules and low density, light weight materials with capacity up to 2 x 25kg bags (depending on model). Robust steel construction complete with safe guarding to head/pan and motor/engine/gearbox. http://www.monstermulch.co.uk/baron-e120-forced-action-mixer-120l-1-1kw-110v-i555.htm

Further technical information available on request.

 
   

 

WETPOUR ROLLERS

Roller straight

Ideal for creating the perfect finish on large difficult to reach areas. All steel construction 114mm diameter roller complete with 1600mm handle. Available in a range of widths – 400mm, 600mm & 800mm.

 
  ROLLER TRAY

Roller Trough

Lightweight fibreglass construction suitable for containing release agent and light solvent. Measures approximately 870mm long x 330mm wide x 160mm high, weight 2.5kgs. 

 
   

WETPOUR TROWEL

Float cropped

Wetpour long-nosed 400mm steel trowel. Ideal for achieving a perfect finish, particularly for intricate areas, graphics and around surface edges.

 
   

DRUM TAP

Drum Tap 1

2″ Treacle drum tap suitable for dispensing viscous fluids. Cast Iron body with brass faceplate for an excellent seal and easy flow control. Can be dismantled for easy cleaning.

   

 

DRUM TROLLEY / STAND

Drum Stand

Drum trolley and pouring stand for 210 litre steel drums (250kgs). Suitable for most terrains. Measures approximately 1,220mm x 800mm wide x 310mm high. Height of bung 360mm, weight 22kgs.

We also stock a static version which is smaller in size.

* Please enquire for advice, materials quotes and installations

 


Share on Facebook Share on Twitter Share on Google+ Share on Linked In Share on Pinterest Email to a friend More options
Share
Share on Facebook

Facebook

Share on Twitter

Twitter

Share on Google+

Google+

Share on Pinterest

Pinterest

Email to a friend

Email

Share on Linked In

Linked In

Share on Instagram

Instagram

Share on Tumblr

Tumblr

Share on Wordpress

Wordpress

Share on your blog

Re-blog

Close
Online - Start Chat?

Your name *

 

Cancel